Stuck in dealer mode? - Suzuki GSX-R Motorcycle Forums Gixxer.com

 
LinkBack Thread Tools Display Modes
post #1 of 10 (permalink) Old 09-09-2018, 02:58 PM Thread Starter
Squid
 
Join Date: Jul 2018
Posts: 10
Stuck in dealer mode?

Good afternoon!

When starting my bike it seems to stay in what I think is dealer mode for 5+ mins or until I start riding it. I am not sure what the issue is it starts and runs perfectly fine though. The picture attached is what the dash shows even while running. Any advice on how to fix the issue would be awesome.
BlueTurd2.0 is offline  
Sponsored Links
Advertisement
 
post #2 of 10 (permalink) Old 09-10-2018, 03:56 AM
I know things... A lot of things.
 
Join Date: Feb 2015
Motorcycle: GSXR 750 K4
Posts: 3,047
Re: Stuck in dealer mode?

I can't see an attached picture. What exactly do you see on the dash? Does it say something like -C00 where the coolant temperature is and then, 5 min later, with no obvious reason, it switches back to showing the temperature as usual?
dpapavas is offline  
post #3 of 10 (permalink) Old 09-10-2018, 08:25 PM Thread Starter
Squid
 
Join Date: Jul 2018
Posts: 10
It did that, but the cluster was super dim (battery was dead) then today after charging it this is what happens now. https://youtu.be/HyH2gwO3kE0
BlueTurd2.0 is offline  
Sponsored Links
Advertisement
 
post #4 of 10 (permalink) Old 09-10-2018, 09:40 PM
You should listen to me. No, seriously, listen to me.
 
Join Date: Oct 2008
Location: Santa Barbara
Motorcycle: Blue 2006 GSX-R1000
Posts: 7,496
Re: Stuck in dealer mode?

There are two power supply lines to the cluster. The R/Bl is always hot while the R is switched. There's also a B/W ground, though the indicator lights suggest that it's OK. Make sure that both supplies are OK, good connections, etc. If they are, there's probably something wrong with the cluster.
BillV is offline  
post #5 of 10 (permalink) Old 09-10-2018, 11:13 PM
Provisional Novice
 
Join Date: Jul 2018
Posts: 137
Re: Stuck in dealer mode?

Fuse blown?
MonkeyRider is offline  
post #6 of 10 (permalink) Old 09-11-2018, 05:04 AM
I know things... A lot of things.
 
Join Date: Feb 2015
Motorcycle: GSXR 750 K4
Posts: 3,047
Re: Stuck in dealer mode?

Apart from what Bill said, do you have reason to believe that the battery is ok? Have you measured the battery voltage with the ignition on? Does the bike crank and start even though the dash is doing that?
dpapavas is offline  
post #7 of 10 (permalink) Old 09-11-2018, 02:03 PM Thread Starter
Squid
 
Join Date: Jul 2018
Posts: 10
The bike cranks and starts just like normal and runs great, I haven't had time to check anything yet but hopefully in the next couple of days I'll check battery and the connections for the cluster.
BlueTurd2.0 is offline  
post #8 of 10 (permalink) Old 09-14-2018, 04:33 PM Thread Starter
Squid
 
Join Date: Jul 2018
Posts: 10
So I believe I found the issue but I am an idiot when it comes to electrical work, is this fixable or am I fucked? https://youtu.be/X5nMz-RP67g
BlueTurd2.0 is offline  
post #9 of 10 (permalink) Old 09-14-2018, 04:53 PM
Track Day Winner
 
gsxdan's Avatar
 
Join Date: Aug 2018
Location: Melbourne, Australia
Motorcycle: 2005 Suzuki GSX-R 750
Posts: 48
The fried connector looks fixable although you will probably need to source a new connector and maybe even re-pin the ends. If you aren't comfortable doing the work yourself I would recommend finding a local auto electrician(or motorcycle shop$$$) and show them some detailed photos
gsxdan is offline  
post #10 of 10 (permalink) Old 09-14-2018, 11:25 PM
You should listen to me. No, seriously, listen to me.
 
Join Date: Oct 2008
Location: Santa Barbara
Motorcycle: Blue 2006 GSX-R1000
Posts: 7,496
Re: Stuck in dealer mode?

Replace both connector bodies and all the pins. Eastern Beaver and Corsa Technic sell kits for that. It's not that hard but get somebody involved if you can't make good crimps or have difficulty removing the existing pins without damaging the wires. However if you're going that far, you might consider switching to a sealed connector like Suzuki did in later years. It will be different than original but should put an end to the corrosion problem. See the Corsa HM-16P & HM-16S. It's not that important but you can study wiring harness pics on ebay to try to use the same wire locations as Suzuki did on the sealed connector.
BillV is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Suzuki GSX-R Motorcycle Forums Gixxer.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
Piecies of orange plastic like particals stuck in my oil pickup screen Rydebmx2322 SRADs (97-00 600 and 96-99 750) 4 07-14-2018 09:14 AM
Dealer mode connector GSXR1000K3 GSX-R1000 General Forum 26 07-08-2018 02:20 AM
Aprilia Racing Completes Dealer Certification Training Program With Seven North Ameri RRW_Feed RoadRacingWorld.com News 0 06-28-2018 12:10 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome