What pissed you off today...

[TT750]

you find out what tap and coil you need?

[ccmhunt]

He's about to make me crazy with this.

[TT750]

lol well you are a source of good info.. take it as a compliment unless he is pissin and moaning about it. if he gives you to much of a hard time threaten to convince his wife to relinquish him to taking the bus

[Armi]

Originally Posted by TT750

you find out what tap and coil you need?

Originally Posted by ccmhunt

He's about to make me crazy with this.

You're going crazy.....put yourself in my shoes

Originally Posted by TT750

lol well you are a source of good info.. take it as a compliment unless he is pissin and moaning about it. if he gives you to much of a hard time threaten to convince his wife to relinquish him to taking the bus

She's doing that already TT....For real dude, she's really pushing the issue of her not being able to take her OWN car!!!
Someone PLEEEASE tell me the right size helicoil, or I feel fate will ahve it tapped instead and run into some other issue.......Can't fing a beeging smiley
Off to work now.....Woke up at 5 to drop the missus to work, I don't finish till 11, won't get to bed till at least 12, then gotta do it all over again
Do I sound like i'm bitchin alot?

[TT750]

did you try Daz? hey mate to tune out the weirdos on the bus just where your full leathers and helmet.. on every turn lean off the seat and put a knee down!!! they will give you a bit of space i bet

[ccmhunt]

PLUG 16x8
There you happy?
you need me to pull one out to verify thread pitch too?

[Armi]

Originally Posted by ccmhunt

PLUG 16x8
There you happy?
you need me to pull one out to verify thread pitch too?

Errr would you hate me, if I said....Yes please I could then order the helicoil

[TT750]

lol ya i looked at that on the fiche the other night but wasnt sure lol 16x8 was correct

[ccmhunt]

I pulled it out, measured it....its 16mm diam x 8mm depth
Looks to be a fine thread, as it makes 4 turms, and I measured the thread pitch @ 1.5mm
Therefore it should be metric ISO 724, M16 x 1.5

[correll1000]

Found out my reg/ rec is faulty.....damn it.......

[Armi]

Originally Posted by ccmhunt

I pulled it out, measured it....its 16mm diam x 8mm depth
Looks to be a fine thread, as it makes 4 turms, and I measured the thread pitch @ 1.5mm
Therefore it should be metric ISO 724, M16 x 1.5

Perfect

[TT750]

You getting a new plug to?

[tlee2989]

i know this isn't my section but i would like to contribute.

i installed a new 520 chain kit with (the first time ive ever run) a -1+2 setup last tuesday, which makes a week tomorrow, and it has rained...poured everyday since then and all i can do is look at it in the garage

[Copper99]

Originally Posted by tlee2989

i know this isn't my section but i would like to contribute.

i installed a new 520 chain kit with (the first time ive ever run) a -1+2 setup last tuesday, which makes a week tomorrow, and it has rained...poured everyday since then and all i can do is look at it in the garage

I feel your pain.

Sounds like the UK Summer...every day...week....month...

[Armi]

Only it's been bloody well snowing all day here....

[TT750]

Snow... hope you sent the kids out to play it was 8 c here today

[Armi]

Originally Posted by TT750

Snow... hope you sent the kids out to play it was 8 c here today

I would've been at work if they were

Snow forecast for the next 3 days....I do hope they're wrong!!!

[Armi]

Originally Posted by ccmhunt

I pulled it out, measured it....its 16mm diam x 8mm depth
Looks to be a fine thread, as it makes 4 turms, and I measured the thread pitch @ 1.5mm
Therefore it should be metric ISO 724, M16 x 1.5

Chris......this is what I need then, right?

http://www.ebay.co.uk/itm/V-Coil-Hel...item1c29c4f20f

Not sure if it comes with EVERYTHING I need........can you confirm, please?

[ccmhunt]

No, it doesn't have the drill bit.

[Armi]

Originally Posted by ccmhunt

No, it doesn't have the drill bit.

That's what I was thinking...I can't find one with the drill bit